Page 1 of 5

Workday

PostPosted: Mon Nov 03, 2008 12:04 pm
by MADDISC
Work day at unger on sunday was ok . Brad Doug Roger and myself worked for about 5 hours.
We worked on hole 5 and cleaned up all of the brush on the fairway. Then we cleared the green on hole 3.
This course needs alot of attention From all of our members. Even if you can only go out for a little while after work or on the weekend for a few hours. with alittle help we can get this course up and running.
thanks Maddisc.

Re: Workday

PostPosted: Mon Nov 03, 2008 12:56 pm
by irwinje
Thanks to Brad, Mark Doug and Roger for showing up on Sunday and helping Unger along the way. Hopefully the next work day we organize there are more people in town to help out. We appreciate all the work you've done out at Unger and we look forward to getting this course in.
Thanks to Dave for marking fairways before leaving for Evansville.

Re: Workday

PostPosted: Mon Dec 01, 2008 9:11 pm
by rill22
when is the next workday for unger?

Re: Workday

PostPosted: Mon Dec 01, 2008 11:41 pm
by irwinje
Work Day: 12.6.08
Jefferson Barracks
Contact: Mark Dudenhoeffer

Re: Workday

PostPosted: Tue Dec 02, 2008 2:51 pm
by irwinje
WORK DAY: UNGER PARK
12.14.08 (the day after Holly Daze)
Contact: Dave Mac: 314.303.1488

Re: Workday

PostPosted: Wed Dec 03, 2008 12:36 pm
by MADDISC
The workday scheduled for 12-06-08 for JB is going to be held for Unger.
I think there are only a few holes left to do.
Once they are done we can start doing pins and signs.
I will try to be there by 10am.
Call myself or dave or brad
314-713-8640
314-303-1488
314-605-5277

Re: Workday

PostPosted: Mon Dec 08, 2008 11:54 am
by MADDISC
This place is coming along nicely. Dave is supposed to meet with the parks dept. to let them know where to mow. Brad finished cutting up the trees on 17 that were laying across the fairway at about 450'.
All told there were about a dozen people that showed up. Hopefully next sunday we put some pins in the ground. Maddisc

Re: Workday

PostPosted: Thu Dec 11, 2008 5:18 pm
by irwinje
Dave and I met with Rick Taylor, our contact at Unger, on Tuesday. We went over the grass areas that need to be cut and walked a majority of the course with the guys from StL co. Parks. These are the guys that we'll see out there from the parks dept. cutting grass etc. their names are Rick and Donald so give them a wave when you see them.
Brad Fortman got even more areas cleared for lawnmower access with his chainsaw
Jim Lucas, Tim Lewis and I worked the auger and drilled the holes for the baskets.
Sunday 12.14.09 Work Day
This will be the last workday before we get baskets in the ground. We'll need some help doing some final clearing but a majority of the time we'll be sinking the sleeves in concrete and defining tee off areas.
We'd appreciate if anyone has any of the following we could use on Sunday...
shovels
rakes
wheel barrow
concrete mixer
stump grinder
wood chipper
hand saw
chain saw

Re: Workday

PostPosted: Fri Dec 12, 2008 12:07 am
by REDARMY
irwinje wrote:Dave and I met with Rick Taylor, our contact at Unger, on Tuesday. We went over the grass areas that need to be cut and walked a majority of the course with the guys from StL co. Parks. These are the guys that we'll see out there from the parks dept. cutting grass etc. their names are Rick and Donald so give them a wave when you see them.
Brad Fortman got even more areas cleared for lawnmower access with his chainsaw
Jim Lucas, Tim Lewis and I worked the auger and drilled the holes for the baskets.
Sunday 12.14.09 Work Day
This will be the last workday before we get baskets in the ground. We'll need some help doing some final clearing but a majority of the time we'll be sinking the sleeves in concrete and defining tee off areas.
We'd appreciate if anyone has any of the following we could use on Sunday...
shovels
rakes
wheel barrow
concrete mixer
stump grinder
wood chipper
hand saw
chain saw


jeff (i'm assuming?), did you happen to parse the thread about the jokerst/west city/unger plan i set-up in the west city forum?

i've got a rake and handsaw i can contribute to the cause, but if we end up tying together the jokerst/west city deal and the unger workday (and get the word out now), that could lead to more hands/equiptment available to ease the process along.

Re: Workday

PostPosted: Fri Dec 12, 2008 8:31 pm
by glg886disc
Hey jeff, i will be out there on sunday. I will also be at the hollydaze and i wondered what time to show up at unger. Plus is there going to be any temporary holes to play. Thank you. Grant
:D